530,30Lei

Disponibilitate:
Cu precomandă
Cod produs:
DSFT-314540
Marca:
INCRA

Nu a fost încă evaluat
Scrie un comentariu
OUT OF STOCK

Wish List   Comparație

The extreme accuracy that made INCRA famous is now available in an extraordinary new family of incremental miter gauges. These features make the Incra miter gauges unique:
 
AngleLOCK: Precision angle indexing teeth are laser cut in solid steel to lock in many positive angle stops in 5° increments (or more dependent on type) over a full 180° range.
GlideLOCK: Four or Six (dependent on type) expansion disks adjust both sides of the bar for ZERO side play, anti-friction travel on all table saws with standard 3/4 inch x 3/8 inch or near-standard miter gauge channels, including Delta, Craftsman, imports, etc. This means that all of INCRA's incredible precision will actually show up in your work because the bar can't wiggle around in the miter slot.
 
Note: The slide guide of this stop and mitre fence fits all 3/4 inch (19 mm) T-slots as found on many machines from anglo-saxon countries and on other imported equipment. As a rule, slots on machines intended for EU countries are of a different size. Make sure before ordering that the slot is in fact 19 mm wide. If not, you cannot use these stops.
 
The NEW INCRA Miter V27 is engineered to provide a high performance, yet low cost upgrade for your Table Saw, Band Saw, Router Table, Disk Sander, Belt Sander or any other tool in need of a better miter gauge. Like all INCRA Miter Gauges, the V27 delivers extreme miter cutting accuracy through the advanced combination of INCRA's exclusive AngleLOCK indexing system and its patented Adjustable GlideLOCKMiter Bar.
 
While the V27 delivers ALL of the accuracy of its bigger INCRA Miter Gauge brothers, its no-nonsense design and compact size make it the most affordable Incra Miter Gauge EVER! Now, the INCRA Miter V27 makes it possible to put an INCRA Miter Gauge in EVERY standard miter channel (3/4 inch) in your shop.
 
Note: INCRA miters require a one time initial calibration before first use. Follow the instructions in the owner's manual.
 
MITER V27 Specifications:
27 positive angle stops
GlideLOCK Miter Bar with 4 expansion points
5° increments
Special stops at plus or minus 22 1/2°
Plus or minus 60° range
 
Size of steel bar: 15-3/4 inch x 3/4 inch x 3/8 inch
(400 mm x 18.7 mm 9.5 mm)
Width slightly undersizes to fit even in near standard miter channels.
Diameter of protractor part: 6-3/4 inch (172 mm)
 
The Miter V27 Universal Mounting Bracket will support any user-made fence as well as any INCRA fence.
 
Because the Miter V27 is designed to fit in all tools with a standard 3/4 inch x 3/8 inch miter channel, the T-clip is removeable since many older or smaller tools have plain miter channels without the "T-slot".
 
Four expansion points adjust for ZERO side play, anti-friction travel on all tools with standard (or near standard) miter gauge channels, including Delta, Craftsman, imports, etc. This means the bar WON'T wiggle around in the miter slot!
 

 

INCRA Miter V27
While the V27 delivers ALL of the accuracy of its bigger INCRA Miter Gauge brothers, its no-nonsense design and compact size make it the most affordable Incra Miter Gauge EVER! Now, the INCRA Miter V27 makes it possible to put an INCRA Miter Gauge in EVERY standard miter channel (3/4 inch) in your shop.

MITER V27 Specifications:
27 positive angle stops
GlideLOCK Miter Bar with 4 expansion points
5° increments
Special stops at plus or minus 22 1/2°
Plus or minus 60° range

Size of steel bar: 15-3/4 inch x 3/4 inch x 3/8 inch
(400 mm x 18.7 mm 9.5 mm)
Width slightly undersizes to fit even in near standard miter channels.
Diameter of protractor part: 6-3/4 inch (172 mm)
v27
The Miter V27 Universal Mounting Bracket will support any user-made fence as well as any INCRA fence.
v27
Because the Miter V27 is designed to fit in all tools with a standard 3/4 inch x 3/8 inch miter channel, the T-clip is removeable since many older or smaller tools have plain miter channels without the "T-slot".
v27
Four expansion points adjust for ZERO side play, anti-friction travel on all tools with standard (or near standard) miter gauge channels, including Delta, Craftsman, imports, etc. This means the bar WON'T wiggle around in the miter slot!
v27 detail
Detai

 

User manual: https://www.incra.com/manuals/miter_v27_manual.pdf

Miter Gauge Brochure: https://incra.com/info/MiterGauge_Brochure.pdf

Incra Product Overview: https://incra.com/info/ProductOverview_2014_web.pdf

Incra Manuals: https://www.incra.com/product_manuals.html

 

Scrie un comentariu

Notă: codul HTML nu este interpretat!

Rău            Bun


Continuă

Livrare

Livrăm rapid în toată ţara prin GLS Curier la tariful unic de 20 lei (indiferent de greutate) | Sau puteți ridica personal produsele din magazinul nostru (Timișoara, str. Divizia 9 Cavalerie, nr. 49, parter.

Contactați-ne

0745 858 618 (L-V, 10:00 - 18:00)
Orar magazin Timișoara: L-V, 10:00 - 18:00
office@finetools.ro